[Regarding rotational resistance and abnormal noise after running.
Our “Metal Grease” is a special lubricant designed to suppress metal contact under high load and high pressure,
Our “Metal Grease” is a special lubricant designed to prevent seizure and wear by reducing metal contact under high loads and high pressures,
It is a special lubricant designed to prevent metal contact under high loads and high pressures to prevent seizure and wear,
It has been adopted by many motorcycle manufacturers.
It is also used for greasing wheel bearings and other parts of the bike.
It is also widely used for greasing parts of motorcycles, including wheel bearings,
It is highly evaluated for its good lubricating performance and durability under normal conditions of use.
On the other hand, depending on the model and condition of the bike (condition of the bearings), it can be used in some cases,
In low-load rotation applications such as wheel bearings, the viscosity of the grease may be strong,
On the other hand, depending on the type of bike and condition (bearing condition), the viscosity of the grease may feel strong, and rotational resistance and abnormal noise may be bothersome.
In some cases, this may cause rotational resistance and abnormal noise.
We assume that there may be a case where rotational resistance and associated abnormal noise may be felt, as pointed out by the customer.
In this case, it is possible that the grease will gradually blend in and settle down to a good condition by using the product for a certain period of time in its current condition.
In this case, we cannot actually see the condition of your bike.
Since we cannot actually see the condition of the customer's bike,
We are not able to see your bike in person, so we can only give you our best guess.
If you are concerned about the current condition,
If you are concerned about the current condition, please consider removing the metal grease and replacing it with “Bell Hammer GOLD Grease No.2”.
If you are concerned about the current condition, please consider removing the metal grease and replacing it with “Bell Hammer GOLD Grease No.2”.
Bell Hammer GOLD Grease No.2” is also available,
Bell Hammer GOLD Grease No.2” is also compatible with rotating parts and forms a good lubricating film even under low loads,
It also has a characteristic to reduce friction and abnormal noise even under low load.
About the properties under high load
As you asked, “metal grease” is a good match for rotating parts,
As you asked, “metal grease” is designed to be especially effective under high loads, high torque, and high temperatures.
Under these conditions, metal-to-metal contact is not recommended.
Under these conditions, the performance of preventing metal-to-metal contact, seizure and wear is maximized.
The maximum performance is achieved by reducing metal-to-metal contact and preventing seizure and wear.
Suitability for Shielded Ball Bearings
Metal grease is suitable for open bearings and sliding surfaces,
Metal grease is suitable for open type bearings and slide surfaces where the condition of the grease is visible,
It is suitable for open type bearings and slide surfaces where the grease condition is visible, and the proper amount of grease will ensure stable performance.
On the other hand, if you use it for shielded ball bearings, the amount of grease and the type of bearing to be sealed inside should be kept to a minimum,
On the other hand, when used in shielded ball bearings, the amount and viscosity of the grease sealed inside the bearing must be adjusted appropriately to ensure the full effect of the metal grease,
If the amount and viscosity of the grease sealed inside the bearing is properly adjusted, the full effect of the metal grease can be obtained.
However, if the grease is too much or the sealed structure is too tight, the performance may not be fully utilized,
However, if the grease is too much or the structure is too tightly sealed, the performance may not be fully utilized,
We would appreciate it if you could exercise caution when using this product.
Suggestion for alternative products
For ball bearings with shields, we have a product with lower viscosity that is suitable for high-speed rotation,
Bell Hammer GOLD Grease No. 2: This product is suitable for rotary and racing applications,
Bell Hammer GOLD Grease No. 2: High performance grease that provides stable lubrication performance even in low load ranges.
Bellhammer GOLD Grease No. 2: High-performance grease with stable lubrication performance even under low loads for rotating and racing applications.
We can propose more suitable products according to the conditions of use, etc., so please feel free to contact us.